3M S10C Instrukcja Użytkownika

1S10CMultimedia ProjectorOperator's GuideThank you for purchasing this projector.• The information in this manual is subject to change without no

10Please refer to the following for connecting your devices.See the rear of the projector. You can see the ports.Connecting to a computerRGB out

111Connect the connector of thepower cord to the AC inlet of theprojector. 12Firmly plug the power cord’s pluginto the outlet.WARNING • Please use ext

12CAUTION Always handle the batteries with care and use them only as directed.Improper use may result in battery cracking or leakage, which could resu

13Operating The Remote ControlATTENTION • Do not drop or otherwise expose the remote control to physicalimpact.• Do not get the remote control wet or

14Power ON/OFFTurning On The PowerWARNING • When the power is ON, a strong light is emitted. Do not look into thelens or vents of the projector.• Turn

15VIDEOASPECTVOLUMEMAGNIFYAUTO BLANKRGBSEARCHONVIDEOASPECTVOLUMEMAGNIFYAUTO BLANKRGBSEARCHONSelecting An Input Signal12Use the zoom ring to adjust the

16Turning Off The Power• Turn the power on/off in right order. Please power on the projector beforethe connected devices. Power off the projector afte

17OperatingAdjusting The VolumeTemporarily Muting The Sound1Press the VOLUME button.As illustrated on the right, a dialog willappear on the screen to

18Adjusting The Position1Press the POSITION button.As illustrated on the right, a dialog will appear on the screento aid you in adjusting the position

19Using The Automatic Adjustment FeatureCorrecting Keystone DistortionsVIDEOASPECTMUTEKEYSTONEFREEZEMENUPOSITIONENTERESC RESETVOLUMEMAGNIFYAUTO BLANKR

Projector Features……………………………………3Preparation……………………………………………………3Part Names……………………………………………………4The Projector ………………………4Attaching The Base ･･･････…………

20Using The Magnify FeatureFreezing The Screen1Press the MAGNIFY (ON) button.The projector enters MAGNIFY mode.2Press the POSITION button, then use th

21Signal SearchingSelecting The Aspect Ratio1Press the SEARCH button.Cycle through input signals, displaying the images of retrieved signals. Ifno sig

22This projector has the following menus: MAIN, PICTURE-1, PICTURE-2, INPUT, AUTO,SCREEN, OPTION. Each of these menus is operated using the same metho

23MAIN MenuWith the MAIN menu, the items shown in the table below can beperformed.Perform each operation in accordance with the instructions in thetab

24PICTURE - 1 MenuWith the PICTURE - 1 menu, the items shown in the Table below can beperformed.Perform each operation in accordance with the instruct

25Item DescriptionMY MEMORYLoad/Save a Setting:Selecting one from the following and then pressing the or the ENTERbutton performs each function.LOAD1

26PICTURE - 2 MenuWith the PICTURE - 2 menu, the items shown in the table belowcan be performed.Perform each operation in accordance with the instruct

INPUT MenuWith the INPUT menu, the items shown in the table below can beperformed. Perform each operation in accordance with the instructions in thet

28Item DescriptionVIDEO NRSelect a Noise Reduction Mode:HIGH ⇔ MIDDLE ⇔ LOW• This function performs only at a VIDEO input or a S-VIDEO input. At a V

29MENUMAINPICTURE-1PICTURE-2INPUTAUTOSCREENOPTIONADJUSTPOWER OFFSEARCHRESET0 minTURN ON: SELECTAUTO MenuWith the AUTO menu, the items shown in the tab

3●Ultra High BrightnessCrisp, ultra-bright presentations is achieved by using a UHB (ultra high brightness) lamp and a highlyefficient optical system.

30SCREEN MenuWith the SCREEN menu, the items shown in the table below can beperformed.Perform each operation in accordance with the instructions in th

31OPTION MenuWith the OPTION menu, the items shown in the table below can be performed.Perform each operation in accordance with the instructions in t

32LampThe projector uses a high-pressure mercury glass lamp. The lamp can break with aloud bang, or burn out, if jolted or scratched, handled while ho

331Turn off the projector, and unplug the power cord. Allow the lampbulb to cool for at least 45 minutes.6Insert the new lamp, and tighten the 2screws

34Air FilterCaring For The Air FilterThe air filter should be cleaned about every 100 hours. If the indicators or a messageprompts you to clean the ai

35Replacing The Air FilterTurn off the projector, and unplug the power cord.2436Reset the filter timer.(1) Turn on the projector. While the projector

36Other CareWARNING • Please carefully read the “Product Safety Guide”.• Before replacing the air filter, make sure the power switch is off and the po

37TroubleshootingRelated MessagesWhen the unit's power is ON, messages such as those shown below may be displayed.When any such message is displa

38Wipe the dust-detectingwindow by using a softTroubleshooting (continued)Related Messages(continued)Message DescriptionCLEAN THE AIR FILTERPOWER OFF

39ATTENTION • When the interior portion has become overheated, for safetypurposes, the power source is automatically turned off, and the indicator lam

Part NamesThe ProjectorIndicates the correspondingreference pageAttaching The BaseFocus ringAir filter cover(An air filter isinside.)34Elevator button

40powerindicatorlampindicatortempindicatorDescriptionLighting orblinking inredTurned offBlinking inredThe cooling fan is not operating. Turn the power

41WARNING • Please carefully read the “Product Safety Guide”.Never use the projector if abnormal operations such as smoke, strange odor, excessivesoun

42PhenomenonCases not involving a machine defect, and Items to be confirmedReferencepagesPictures appeardark.The brightness setting and/or contrast se

Item SpecificationProduct name Liquid crystal projectorLiquidcrystalpanelPanel size 1.4 cm (0.55 type)Drive system TFT active matrixPixels 480,000 pix

44Acccessories...Part NumberUHB lamp, 130W ...

Intended UseBefore operating this machine, please read this entire manual thoroughly. The 3MTM Multimedia Projectors are designed, built, and tested f

5Control buttonsPart Names (continued)The Projector (continued)keystone buttonturns on/off the KEYSTONEmode.In the KEYSTONE mode,To adjust the keyston

6The Remote ControlSTANDBY/ONbuttonprepares for turning thepower on/off.VIDEO buttontoggles between the signal ports of video, s-videoand component vi

7Setting UpArrangementWARNING • Install the projector in a suitable environment according toinstructions of the “ProductSafety Guide” and this manual.

8Adjusting The Projector's ElevatorCAUTION • If you press the elevator buttons without holding the projector, theprojector might crash down, over

9Connecting Your DevicesWARNING • Incorrect connecting could result in fire or electrical shock.Whenever attempting to connect other devices to the pr